INVERTERS

Xantrex SW Inverter/Charger   The SW Inverter/Charger is available in 24- and 48-volt models, provides utility-grade output power and offers high surge capacity to run most household appliances.  The SW includes programmable features such as automatic generator start and stop and automatic load sensing. The three-stage battery charger is built-in and fully automatic, designed to bring maximum charge to batteries, while minimizing generator run time and fuel. Grid Tie: Using the Xantrex Grid Tie Interface (GTI), the SW converts energy from multiple renewable energy sources, such as solar, wind, and microhydro, into AC powery. Software/hardware revision 4.2 or higher is required to connect the SW4024, SW4048, or SW5548 to the GTI.

	Xantrex SW Plus Inverter/Charger   The SW Plus is designed to provide a completely independent power supply to homes. The SW Plus 2500, 4000 and 5500 Inverter/Chargers combine an inverter, battery charger and dual transfer switch in one package. The SW Plus comes in 24- and 48-volt versions, and features continuous power output of 2.5, 4.0 and 5.5 kVA. The SW Plus provides AC power for household appliances and DC power to charge batteries. It converts all forms of renewable energy into utility grade household power as part of an off-grid renewable power system.
	DR Inverter/Charger - 120 VAC/60 Hz   The DR Inverter/Charger provides dependable modified sine wave power for businesses, homes and workshops. Available in 1500, 2400 or 3600 watt models, it can power most common electrical appliances such as lights, televisions, cash registers, refrigerators, washing machines, computers, and power tools.  The DR’s high surge capacity gives it the ability to start difficult motor loads. Once set up, all functions of the inverter/charger are fully automatic.
	Xantrex Gt Series Grid Tie Solar Inverters   Same great features and benefits as all Xantrex GT Series Grid Tie Solar Inverters in a 3800 watt size.   These units are highly efficiency and feature outstanding energy harvest in a small, modular design.  Easy to install due to the included mounting back plate and easy access wiring box for clean looking multi unit installations.  Features: Included communication ports, LCD display with back-light for 24 hour display viewing, convection cooled therefore not requiring a fan and compatible with other GT Series models to custom size the inverters to the array.  Light enough for single person installation.

	Outback FX   The OutBack FX series is a modular "building block” sine wave inverter/charger that can be used for both small and large power systems. Each OutBack FX inverter/charger is a complete power conversion system - DC to AC inverter, battery charger and AC transfer switch. Additional FX inverter/chargers can be connected at any time in either parallel (120 VAC), series (120/240 VAC), or three-phase (120Y208 VAC) configurations.
	Outback VFX   VFX series is a modular "building block” sine wave inverter/charger that can be used for both small and large power systems. Each OutBack VFX inverter/charger is a complete power conversion system - DC to AC inverter, battery charger and AC transfer switch. Additional VFX inverter/chargers can be connected at any time in either parallel (120 VAC), series (120/240 VAC), or three-phase (120Y208 VAC) configurations. This allows a system to be tailored to meet the specific power conversion requirements of the application, both at the time of the installation and in the future.
	Outback GTFX   The OutBack modular "building block" sinewave inverter/chargers can be used for both residential and commercial applications. Each OutBack inverter/charger module is a complete power conversion system - DC to AC inverter, battery charger and AC transfer switch. Additional inverter/chargers can be connected at any time in either parallel (120VAC), series (120/240VAC) or even three phase (120Y240VAC) configuration, allowing the system to be tailored to the specific power conversion requirements of your application. Up to ten of FX or VFX inverter/chargers can be connected together to provide up to 36 kW of continuous power conversion capacity using a HUB10 communication manager and a MATE system display.

• Batteries

• Charge Controllers

• Module Mounts